Grizzly G0845P Owner'S Manual Download Page 44 | Manualshive

Page: 44 / 68

background image

-42-

Model G0845P (Mfd. Since 01/18)

8. While assistant holds keyed flat head cap

screw at front of upper blade, loosen but DO
NOT remove (7) corresponding hex nuts and
(7) flat washers on back of blade frame (see

Figure 61).

Figure 61. Upper blade hex nut removal (rear

work stop and rear cover removed for clarity).

Upper Blade Hex Nuts

9. Put on heavy leather gloves, then remove (7)

hex nuts and (7) flat washers before pulling
upper blade and (7) upper keyed flat head
cap screws from frame.

Items Needed

Qty

Hex Wrench 10mm ............................................ 1
Hex Wrench 4mm .............................................. 1
Open-End Wrench 25mm .................................. 1
Another Person .................................................. 1
Heavy Leather Gloves .............1 Pair Per Person
Mineral Spirits .................................... As Needed
Shop Rags ......................................... As Needed

Reversing & Replacing Lower Blade

1. DISCONNECT MACHINE FROM POWER!

2. Remove front cover, rear cover, and rear

work stop assembly.

3. Have assistant wearing heavy leather gloves

hold  keyed  flat  head  cap  screws  at  rear  of
machine.  Working  from  front  of  machine,
loosen  but  do  not  remove  (7)  hex  nuts  and
flat  washers  securing  lower  blade  to  rear  of
table (see

Figures 62 & 63).

10. Installation is reverse of removal.

IMPORTANT: Align keyed flat head cap
screws with slots in blade before tightening
fasteners. Check blade gap after installing
blade (see

Page 38).

Note: Clean mounting surface and blade with
mineral spirits before re-installing blade.

Figure 63. Location of keyed flat head cap

screws in lower blade.

Keyed Flat Head Cap Screws

Figure 62. Location of hex nuts and flat washers

securing lower blade to frame.

Lower Blade Hex Nuts (6 of 7)

OFF

ON

6. Move rear work stop assembly all the way

forward.

7. Place 1x4 and 2x4 wood blocks on top of

table and rear stop assembly to support
upper blade should it slip during

Step 9.

If shear does not start after reassem-

bly, inspect blade guard limit switch. The

shear will not operate if the finger guard is

removed or does not engage the limit switch

after reassembly. If necessary, adjust finger

guard position and/or limit switch mounting

plate to engage limit switch.

«
...
42
43
44
45
46
...
»

Summary of Contents for G0845P





































































Reviews:

No comments

Related manuals for G0845P

Brand: Panasonic Pages: 172

Brand: REDSTONE Pages: 70

Performance IntelliSUPPLY PSC15

Brand: XS Power Batteries Pages: 24

Brand: Bench Dog Tools Pages: 12

Brand: Ferm Pages: 96

Brand: Desoutter Pages: 8

Brand: Rockwell Automation Pages: 4

Brand: BK Precision Pages: 92

Brand: MAG TOOLS Pages: 2

Brand: BGS technic Pages: 4

GT-86121-1224-W2E

Brand: W&T Pages: 14

Brand: Agilent Technologies Pages: 179

Brand: Narex Pages: 32

Brand: Baileigh Industrial Pages: 44

Brand: StarTech.com Pages: 4

Brand: Lutool Pages: 21

Brand: Meec Pages: 24

Brand: POWER ON BOARD Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands