Grizzly G0845P Owner'S Manual Download Page 36 | Manualshive

Page: 36 / 68

background image

-34-

Model G0845P (Mfd. Since 01/18)

Rear Work Stop Support Rods

Lubrication Frequency ..................... Every Month

Keep the rear work stop support rods lubricated
for smooth operation.

Connecting Rod Pin Shafts

Lubrication Frequency ..................... Every Month

The connecting rods transfer power between
the eccentric cams and upper blade frame. The
pin shaft links the connecting rod with the upper
blade frame.

Items Needed

Qty

Stiff Cleaning Brush .......................................... 1
Shop Rags ......................................... As Needed
Mineral Spirits .................................... As Needed
NLGI#2 Grease or Grizzly T26419 .... As Needed
ISO 68 Oil or Grizzly T27914 ............. As Needed

To lubricate rear work stop support rods:

1. DISCONNECT MACHINE FROM POWER!

2. Use mineral spirits and stiff cleaning brush to

clean gear racks on bottom of support rods
(see

Figure 46).

3. Wipe support rods clean with mineral spirits.

Allow to air dry.

4. Apply light coating of ISO 68 machine oil or

equivalent on upper surface of support rods.

5. Apply light coating of NLGI #2 grease or

equivalent to gear racks.

6. Move work stop assembly across support rods

several times to evenly distribute lubricant.

Figure 46. Rear work stop support rod

lubrication.

Gear

Racks

Items Needed

Qty

Grease Gun ....................................................... 1
NLGI#2 Grease or Grizzly T26419 .... As Needed
Shop Rags ......................................... As Needed

To lubricate connecting rod pin shafts:

1. DISCONNECT MACHINE FROM POWER!

2. Clean area around grease fittings on bottom

of blade frame where shown in

Figure 47.

3. Pump in new grease until it just seeps from

fitting. Repeat for second grease fitting.

4. Run machine through several cutting cycles

to evenly distribute grease.

Main Shaft Roller Bearings

Lubrication Frequency ................ Every 6 Months

Grease the four main shaft roller bearings when-
ever changing the gearbox oil.

Items Needed

Qty

Grease Gun ....................................................... 1
Hex Wrench 4mm .............................................. 1
Shop Rags ......................................... As Needed
NLGI#2 Grease or Grizzly T26419 .... As Needed

Figure 47. Connecting rod lubrication.

OFF

ON

OFF

ON

Connecting

Rod Grease

Fittings

Support Rods

«
...
34
35
36
37
38
...
»

Summary of Contents for G0845P





































































Reviews:

No comments

Related manuals for G0845P

Brand: jbc Pages: 8

ASCM18QM Series

Brand: Fein Pages: 20

Brand: Laser Pages: 2

Brand: Q-tran Pages: 5

Brand: NSI Solutions Pages: 10

Brand: Performance Tool Pages: 6

Brand: Moog Pages: 15

Brand: Campbell Hausfeld Pages: 32

Brand: Wacker Neuson Pages: 36

Brand: WAGO Pages: 44

Brand: P.Lindberg Pages: 33

Brand: YATO Pages: 112

Brand: Pepperl+Fuchs Pages: 26

Brand: Northern Pages: 11

Brand: Parkside Pages: 28

Brand: MATO Pages: 17

Brand: Banner Pages: 2

Brand: Ebinger Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands