GREENLINE E6CCXLX Operation Manual Download Page 5

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

5

E6CCXLX Battery-powered Tool

Identification

  1.  LED Work Light (white)
  2.  Adapter Release Buttons
  3. Head
  4.  Latch (for opening head)
  5.  Lanyard Ring
  6. Housing
  7.  Retract Button
  8.  LED Indicator (red)
  9.  LCD Screen
10. Battery
11. Trigger

3

4

1

11

10

5

8

7

6

9

2

Specifications

Tool

Length ...............................................................................................15.3" (388 mm)
Width ...................................................................................................3.00" (76 mm)
Height (with battery) ..........................................................................12.9" (328 mm)
Weight ................................................................................................10.2 lb (4.6 kg)
Crimping Force ................................................................................. 6.7 tons (60 kN)
Hydraulic Oil ...............................................52057878 biodegradable hydraulic fluid
Recommended Operating Temperature Range ..............5 °F to 122 °F (–15 °C to 50 °C)

Crimping Tool

Maximum Crimping Cable Size ................... 600 kcmil copper; 350 kcmil aluminum

Cutting Tool

Maximum Cutting ................................... 1-1/2" (40 mm) kcmil aluminum or copper

Battery Charger .............................................................Read the instructions supplied  

with the battery charger

Summary of Contents for E6CCXLX





















Reviews: