GREENLINE E6CCXLX Operation Manual Download Page 4

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

4

E6CCXLX Battery-powered Tool

IMPORTANT SAFETY INFORMATION

Do not dispose of batteries in a fire. They will vent 

fumes and may explode.
Failure to observe this warning could result in severe 

injury from harmful fumes or burns from flying debris.

Remove the battery before transporting the T version 

of this tool by air.
Failure to observe this warning could result in severe 

injury or death.

•  Inspect tool and dies before use. Replace any 

worn or  damaged parts. A damaged or improp-

erly  assembled tool can break and strike nearby 

personnel. 

•  Carrying strap is for carrying only, not to be used to 

hang or suspend tool. 

Failure to observe these warnings could result in 

severe injury or death.

•  Do not use this tool for continuous use. After 30 to 

40 cycles, allow the tool to cool for 15 minutes.

•  Do not secure this tool in a vise. This tool is 

designed for hand-held operation.

•  This tool may be used in damp or wet environ-

ments; however, air-drying is recommended before 

use if the tool becomes soaked. Damage may result 

when the tool is operated prior to thorough drying 

when electrical components are soaked.

•  Use this tool for the manufacturer’s intended 

purpose only.

Failure to observe these precautions may result in 

injury or property damage.

Do not allow anything to contact the battery 

terminals.
•  Do not immerse the batteries in liquid. Liquid may 

create a short circuit and damage the battery. If bat-

teries are immersed, contact your service center for 

proper handling.

•  Do not place the battery into a pocket, tool pouch, 

or tool box with conductive objects. Conductive 

objects may create a short circuit and damage the 

battery.

•  Do not place a battery on moist ground or grass. 

Moisture may create a short circuit and damage the 

battery.

Failure to observe these precautions may result in 

injury or property damage.

•  Do not store the battery at more than 122 °F (50 °C) 

or less than –4 °F (–20 °C). Damage to the battery 

can result.

•  Do not use another manufacturer’s charger. Other 

manufacturers’ chargers may overcharge and 

damage the battery.

•  Do not attempt to open the battery. It contains no 

user-serviceable parts.

Failure to observe these precautions may result in 

injury or property damage.

Do not perform any service or maintenance other than 

as described in this manual. Injury or damage to the 

tool may result.
Failure to observe this precaution may result in injury 

and property damage.

Note:  Keep all decals clean and legible, and replace 

when necessary.

Summary of Contents for E6CCXLX





















Reviews: