GREENLINE E6CCXLX Operation Manual Download Page 2

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

2

E6CCXLX Battery-powered Tool

Description

E6CCXLX Battery-powered, High-speed Tool is a hand-

held, self-contained tools intended to crimp cable, 

cut cable and threaded rod, and punch holes with the 

proper adapters.
The tools has a retraction stop feature which allows 

the operator to stop the retraction motion of the ram to 

shorten cycle time.
The tool has a Bluetooth

®

 connectivity and an LCD 

screen. 
The tool is a protected by U.S. Patent No. 6,206,663, 

6,276,186, 6,401,515, and 6,532,790.

 

Model X-E6CCXLX—FCC ID: 2AGL2X; IC ID: 20646X

This device complies with Part 15 of the FCC Rules and 

with Industry Canada licence-exempt RSS standard(s). 

Operation is subject to the following two conditions: 

(1) this device may not cause harmful interference, and 

(2) this device must accept any interference received, 

including interference that may cause undesired 

operation

Note: Change or modifications made to this equipment 

not expressly approved by Greenlee may void the FCC 

authorization to operate this equipment.

Safety

Safety is essential in the use and maintenance of 

Greenlee tools and equipment. This manual and any 

markings on the tool provide information for avoiding 

hazards and unsafe practices related to the use of this 

tool. Observe all of the safety information  provided.

Note: For body worn operation, this device has been 

tested and meets the FCC RF exposure guidelines for 

an uncontrolled environment. The maximum reported 

SAR value is 0.08 mW/g

Purpose of this Manual

This manual is intended to familiarize all personnel with  

the safe operation and maintenance procedures for the 

following Greenlee tool:
•  E6CCXLX Battery-powered, High-speed Tool
Keep this manual available to all personnel.
Replacement manuals are available upon request at  

no charge at www.greenlee.com.

Do not discard this product or throw away!

  

For recycling information, go to www.greenlee.com.

All specifications are nominal and may change as design 

improvements occur. Greenlee Textron Inc. shall not be liable for 

damages resulting from misapplication or misuse of its products.
GATOR and Kwik Stepper are registered trademarks of 

Textron Innovations Inc.
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Blackburn is a registered trademark of Thomas & Betts.

KEEP THIS MANUAL

Table of Contents

Description .................................................................... 2
Safety ............................................................................ 2
Purpose of this Manual ................................................. 2
Important Safety Information .....................................3–4
Identification .................................................................. 5
Specifications ................................................................ 5
Operation ..................................................................6–14
 Crimping .................................................................7–8
 Cutting ....................................................................... 9
 Punching .............................................................10–14
Available Adapters ....................................................... 15
Die Selection ............................................................... 16
Connector Selection .................................................... 16
LCD Screen ................................................................. 17
Maintenance ................................................................ 18
Troubleshooting ........................................................... 19

Summary of Contents for E6CCXLX





















Reviews: