Gree LIVV09HP230V1A Series Service & Parts Manual Download Page 80

Page: 80 / 120

131

Service Manual

(8) Overload and high discharge temperature malfunction

Main detection points:

●

If the electronic expansion valve is connected well? Is the electronic expansion valve damaged?

●

If the refrigerant is leaked?

●

The compressor overload protection terminal is not connected well with the mainboard?

●

If the overload protector is damaged?

●

Heat exchange of unit is not good? (heat exchanger is dirty and unit radiating environment is bad)

●

Too much load of the system causes high temperature of compressor after working for a long time?

●

Malfunction of discharge temperature sensor?

Summary of Contents for LIVV09HP230V1A Series

























































































































Search results

Summary of Contents for LIVV09HP230V1A Series

Reviews:

Related manuals for LIVV09HP230V1A Series

Brands by name

Popular brands

Gree LIVV09HP230V1A Series, Service & Parts Manual

Search results

Summary of Contents for LIVV09HP230V1A Series

Reviews:

Related manuals for LIVV09HP230V1A Series

Brands by name

Popular brands