Gree LIVV09HP230V1A Series Service & Parts Manual Download Page 105

Page: 105 / 120

192

Service Manual

3.Remove grille and front panel

4.Remove axial flow blade

5.Remove right side plate

Remove connection screws between the front grille

and the front panel. Then remove the front grille.

Remove connection screws connecting the front

panel with the chassis and the motor support, and

then remove the front panel.

Remove the nut fixing the blade and then

remove the axial flow blade.

Remove connection screws connecting the right

side plate with the valve support and the electric

box. Then remove the right side plate.

Grille

Panel

Axial flow blade

Right side plate

102

Summary of Contents for LIVV09HP230V1A Series

























































































































Search results

Summary of Contents for LIVV09HP230V1A Series

Reviews:

Related manuals for LIVV09HP230V1A Series

Brands by name

Popular brands

Gree LIVV09HP230V1A Series, Service & Parts Manual

Search results

Summary of Contents for LIVV09HP230V1A Series

Reviews:

Related manuals for LIVV09HP230V1A Series

Brands by name

Popular brands