background image

 

   

Contents

1 Safety Precautions ................................................................................................ 1

 

2 Product Introduction ............................................................................................. 2

 

2.1 Names of Key Components ............................................................................................ 2

 

2.2 Rated Working Condition ................................................................................................ 2

 

3 Preparations for Installation ................................................................................. 2

 

3.1 Standard Fittings ............................................................................................................. 2

 

3.2 Installation Position Selection ......................................................................................... 3

 

3.3 Requirements for Communication Line ........................................................................... 4

 

3.4 Wiring Requirements ...................................................................................................... 6

 

4 Installation Instructions ........................................................................................ 6

 

4.1 Installation of Indoor Unit ................................................................................................ 6

 

4.2 Refrigerant Pipe Connection ........................................................................................... 8

 

4.3 Drainage Pipe Installation and Drainage System Testing ............................................... 9

 

4.4 Panel Installation ........................................................................................................... 12

 

4.5 Installation of Wired Controller ...................................................................................... 13

 

5 Wiring Work ......................................................................................................... 14

 

5.1 Connection of Wire and Patch Board Terminal ............................................................. 14

 

5.2 Power Cord Connection ................................................................................................ 15

 

5.3 Connection of Communication Wire between Indoor Unit and Outdoor Unit (or Indoor 
Unit) .................................................................................................................................... 15

 

5.4 Connect Communication Wire of Wired Controller ....................................................... 16

 

5.5 Illuminate for Connection of Wired Controller and Indoor Units Network ...................... 17

 

6 Routine Maintenance........................................................................................... 19

 

6.1 Cleaning of Filter ........................................................................................................... 19

 

6.2 Maintenance before the Seasonal Use ......................................................................... 19

 

6.3 Maintenance after the Seasonal Use ............................................................................ 19

 

7 Table of Error Codes for Indoor Unit .................................................................. 19

 

8 Troubleshooting .................................................................................................. 20

 

 

 

Summary of Contents for GMV-ND07TD/A-T


























Reviews: