background image

Multi Variable Air Conditioners One-way Cassette Type Indoor Unit 

11 

Unit: mm(inch) 

 

Fig.4.3.4 

4.3.3 Test of Drainage System 

(1)  Please test drainage system after electric work is finished. 

Inject approximately 1L purified water to drain pan from air vent, ensure that not to splash the 

water over the electrical components (e.g. water pump. etc.). 

1)  Inject approximately 1L purified water to drain pan from air vent, ensure that not to 

splash the water over the electrical components (e.g. water pump etc.). 

2)  In case of commissioning finished, please energize the IDUs and switch to cooling or 

dry mode, meanwhile, the water pump operates, you can check the draining through 

the drain socket. 

3)  If communication wire is not connected, communication malfunction “C0” will occur 

after 60s of energizing. In this case, the water pump operates automatically. Check if 

the water pump  drains normally through drainage port. The water pump will stop 

automatically after running for 10mins. 

(2)  During the test, please carefully check the drainage joint, make sure no any leakage 

occur. 

(3)  It’s strongly recommend to do the drain test before ceiling decoration. 

Unit:mm(inch) 

 

Fig.4.3.5 

 

 

Summary of Contents for GMV-ND07TD/A-T


























Reviews: