background image

GREE

Multi Variable Air Conditioners Indoor Unit

161

4.2 Slim Duct Type Indoor Unit

NOTICE!

The following steps are specific for GMV-ND24PLS/B-T(U) units. For other units, the assembly

and disassembly procedure is similar except the numbers of louvers and motors.

Motor and fan

Precondition: The power supply has been disconnected.

Step

Diagram

Operation Procedure

(1) Remove the

air return filter.

Draw the air return filter to both
sides respectively at the return air
inlet.

(2) Remove the

cover plate of
the electric
box.

Disconnect the power supply of
the IDUs, use a screwdriver to
unscrew the cover plate of the
electric box, and then remove the
line connecting to the motor.

(3) Remove the

rear volute
casing.

Loosen the fasteners that connect
the rear volute casing with the
front volute casing and remove
the rear volute casing.

(4) Remove the

front volute
casing.

Use a screwdriver to unscrew the
front volute casing and then
remove the volute casing.

(5) Remove the

louver and
motor.

Use a screwdriver to unscrew the
louver and loosen the fasteners of
the motor.

(6) Install a new

motor.

Remove the motor from the
support and remove the louver
from the motor. Then, remove the
motor.

Install a new motor.

(7) Install units in

a reverse
order of this
procedure.

Assemble units based on the
reverse order of this procedure
and power on the units for test.

Summary of Contents for CM100N1480











































































































































































































































































Reviews: