background image

GREE                                                          Duct type split Air conditioner Inverter Series

 

74 

 

Flow-process diagram of debugging: 

01:Set master unit

02:Allocate addresses

03:Confirm the quantity of ODU

04:Confirm the quantity of IDU

07:Detect indoor components

06:Detect outdoor components

05:Detect ODU

s internal communication

08:Confirm preheated compressor

09:Confirm status of valve of ODU

10:Debugging completed status

 

1.4.4 Debugging process 

(1)  Unit manufactured before Oct 30,2018. 
Debugging procedure for test run, display instruction for indicator on main board of outdoor unit and 

operation method are as below: 

Description of each stage of debugging progress 

—— 

Debugging Code 

Instruction for Code and Operating Method 

Progress 

LED 

Display Code 

Display 

Code 

Start 

A0 

Always 

ON 

No debugged yeat. Press “SW3” button consecutively in the 

master module for over 5s to enter auto debugging. 

01_ Set master 

unit 

01/CC 

Display 

repeatedly 

There is no master unit in the system.   

The system cannot continue to conduct debugging, and all the 

buttons are invalid that must be reset by cutting the power. 

01/CF 

Display 

repeatedly 

There are two or more master units in the system.   

The system cannot continue to conduct debugging, and all the 

buttons are invalid that must be reset by cutting the power. 

Please set the correct “SA6” DIP switch. 

01/oC 

Display 

repeatedly 

There is only one master unit in the system.   

The unit will automatically enter into the next step after 

displaying for once. 

Summary of Contents for CF01000730


































































































































Reviews: