Gree CF01000730 Service Manual Download Page 65

Page: 65 / 129

GREE Duct type split Air conditioner Inverter Series

2) The connection method of communication wires.

4.5 Fixing and damping of unit

The outdoor unit shall be fixed with 4 M12 bolts and closely contacted with the foundation. Otherwise,

big vibration and noise will be caused.

The outdoor unit shall be fixed firmly. The rubber board with thickness over 20mm or corrugated

rubber damping pad shall be applied between the unit and foundation.

4.6 Outline dimension and position of installation hole

When carrying the outdoor unit, hang the unit in four directions with two sufficient ropes. In order to

avoid excursion from the center, the angel of ropes must be smaller than 40º during hanging and moving.

Summary of Contents for CF01000730


































































































































Search results

Summary of Contents for CF01000730

Reviews:

Related manuals for CF01000730

Brands by name

Popular brands

Gree CF01000730, Service Manual

Search results

Summary of Contents for CF01000730

Reviews:

Related manuals for CF01000730

Brands by name

Popular brands