manualshive.com logo in svg

GReddy e-01, Instruction Manual, Page: 35 / 55

Share
Download
GReddy e-01 Instruction Manual Download Page 35

C  DISPLAY

34

Changing Setting in display mode

                            PEAK

HI, LO boost selection, SET BOOST , GAIN, START BOOST can 
be adjusted in any of the Digital, Graph, Gauge, and Bar graph 
display mode. 

Press the SET knob to move the cursor to the target setting.
Turn the SET knob to make changes.
Press the SET knob again to confirm the setting. 

* Press the MENU button to cancel at any time.

PEAK HOLD Reset

To clear the stored Peak Hold data, hold down the up button on the 
4-way navigation button for 2 seconds. 

LOCK Feature

This feature is used to lock all the settings to prevent any problems. 
To lock, press down the MENU button and SHIFT button for 5 
seconds. 
Repeat the same procedure to unlock.
Lock feature can only be set in the Display mode. 
When the unit is locked, the message shown is displayed and the 
"LOCK" will appear in the upper right hand corner of the title bar.

    

Pres the SET knob

HI / LO
    

Pres the SET knob

  

SET
    

Pres the SET knob

GAIN
    

Pres the SET knob

START BOOST
    

Pres the SET knob

Cursor will disapear

e-01英語版  03.3.19 20:29  ページ 35

Summary of Contents for e-01
























































Reviews:

No comments