background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY 

Modifications reserved. No liability for printing errors      04/2011    

20 

 

handle  and  operate  the  model  with  the  greatest  care  and  consideration  at  all 
times. 

 
Before  flying  the  aircraft  for  the  first  time  please  check  that  your  private  third  party 
insurance policy provides cover when operating models of this type. If you are unsure 
about this, it is always best to take out a special RC model insurance policy. 
These safety notes must be kept in a safe place. If you ever dispose of the model, be 
sure to pass them on to the new owner. 

 
Manufacturer’s declaration: 

If material defects or manufacturing faults should arise in a product distributed by us 
in the Federal Republic of Germany and purchased by a consumer (§ 13 BGB), we, 
Graupner GmbH & Co. KG, Henriettenstraße 94-96, D-73230 Kirchheim/Teck, 
Germany, acknowledge the obligation to correct those defects within the limitations 
described below. 
The consumer is not entitled to exploit this manufacturer’s declaration if the failure in 
the usability of the product is due to natural wear, use under competition conditions, 
incompetent or improper use (including incorrect installation) or external influences. 
This manufacturer’s declaration does not affect the consumer’s legal or contractual 
rights regarding defects arising from the purchase contract between the consumer 
and the vendor (dealer). 
 
Extent of the guarantee 
 
If a claim is made under guarantee, we undertake at our discretion to repair or 
replace the defective goods. We will not consider supplementary claims, especially 
for reimbursement of costs relating to the defect (e.g. installation / removal costs) and 
compensation for consequent damages unless they are allowed by statute. This does 
not affect claims based on legal regulations, especially according to product liability 
law. 
 
Guarantee requirements 
 
The purchaser is required to make the guarantee claim in writing, and must enclose 
original proof of purchase (e.g. invoice, receipt, delivery note) and this guarantee 
card. He must send the defective goods to us at his own cost, using the address 
stated above. 
The purchaser should state the material defect or manufacturing fault, or the 
symptoms of the fault, in as accurate a manner as possible, so that we can check if 
our guarantee obligation is applicable. 
The goods are transported from the consumer to us and from us to the consumer at 
the risk of the consumer. 
 
Duration of validity 
 
This declaration only applies to claims made to us during the claim period as stated 
in this declaration. The claim period is 24 months from the date of purchase of the 
product by the consumer from a dealer in the Federal Republic of Germany (date of 
purchase). If a defect arises after the end of the claim period, or if the evidence or 
documents required according to this declaration in order to make the claim valid are 

Summary of Contents for YAK 11 RENO























Reviews: