background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY 

Modifications reserved. No liability for printing errors      04/2011    

18 

 

 

Model fuels are volatile and highly inflammable. Keep them well away from 
open  flames,  excessive  heat,  all  possible  sources  of  sparks  and  anything 
else which could result in a fire. Do not smoke in the immediate vicinity of 
fuel or fuel vapours. 

 

Model engines generate a lot of heat. The engine and silencer in particular 
become very hot when running, and stay at a high temperature for quite a 
while.  Touching  the  hot  parts  can  give  you  serious  burns,  so  take  care 
especially  when  carrying  out  adjustments  -  wear  protective  gloves.  Hot 
engines can even start a fire under certain circumstances. 

 

When  the  engine  is  running  it  expels  hot  toxic  gases  from  the  exhaust 
together with very hot fluid combustion residues which can burn you if you 
are not careful. 

 

Remove all unused fuel from the fueltank and engine after every session. 

 

Every  time  you  intend  to  operate  your  model  check  carefully  that  it  and 
everything attached to it (e.g. propeller, linkages, control surfaces etc.) is in 
good  condition  and  undamaged.  If  you  find  a  fault,  do  not  fly  the  model 
until you have corrected it. 

 

Model engines are usually started with the help of an electric starter which 
should be fitted with the appropriate adapter where necessary. With fixed-
wing  models  an  alternative  is  to  use  a  “chicken  stick”  -  a  length  of  thick 
wooden dowel with a piece of water hose pushed over it 

 

Many model engines are very noisy, producing a sound level much higher 
than 85 dB (A-weighted), which implies that you should wear ear defenders. 
Never run a engine without the silencer fitted. Even with a silencer, model 
engines can easily disturb your neighbours. Don’t run engines when other 
people expect peace and quiet. 

 

If  you  start  your  engine  when  the  model  is  standing  on  loose  or  sandy 
ground, the propeller will suck up sand and dust and hurl it around, and it 
could  easily  get  in  your  eyes  and  do  damage.  Wear  protective  goggles  at 
such times. 

 

Take  care  that  the  sparkplug  clip  and  the  lead  cannot  get  tangled  in  the 
propeller or other rotating parts. Check the throttle linkage too. 

 

Take particular care when carrying the model with the engine running. Hold 
the rotating parts well away from you! 

 

Be sure to keep an adequate supply of fuel in the tank. Don’t continue to fly 
the model until the tank is drained dry. 

 

Never fly directly over people. 

 

Never fly directly towards people. 

 

Keep  a  safe  distance  from  residential  areas:  at  least  1.5  km  ‘as  the  crow 
flies’. The best solution is to join a model flying club and use the approved 
flying site. Always keep well clear of high-tension overhead cables. 

 

Whenever you are working on the engine, make sure that you are on a safe 
surface and cannot slip. Get used to holding the model really securely. 

 

Take-off and landing strips should be kept free of unauthorised people and 
movable obstacles, particularly when a model is using the strip. 

 

Watch  the  aeroplane  constantly  while  it  is  in  the  air.  Models  must  always 
give way to full-size aircraft. 

Summary of Contents for YAK 11 RENO























Reviews: