background image

16

This product must not be disposed of with other waste.

Instead, it is the user’s responsibility to their waste

equipment by handing it over to a designated collection

point for the recycling of waste electrical and 

electronic equipment. The separate collection and recycling

of your waste equipment at the time of disposal will help to conserve 

natural resources and

ensure that it is recycled in a manner that protects human health and 

the environment. For more

information about where you can drop off your waste equipment for 

recycling, please contact your

local city office, your household waste disposal service or where you 

purchased the produce

  ◎ 

E

NVIRONMENTAL PROTECTION NOTES

•  

NOTE

This equipment has been tested and found to comply with the limits 
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment 
generates uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause 
harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. 
If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference 
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-  Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for 
help.

•  

FCC radiation exposure statement

This equipment complies with FCC radiation exposure limits set forth 
for an uncontrolled environment. This equipment should be installed 
and operated with minimum distance of 20 cm between the radiator 
and your body.

Summary of Contents for X-4S HoTT SJ

















Reviews: