background image

15

(1) KC Information

 

  

Graupner/SJ X-4S Transmitter

  KCC인증번호: MSIP-CRM-sjr-16005900

  Graupner/SJ GR-4 Receiver
  KCC인증번호: MSIP-CRM-sjr-16005600

- 방송통신위원회고시 제2013-01호
- 방송통신위원회고시 제2012-102호 “신고하지
  아니하고 개설할 수 있는 무선기기”

- EN 62479:2010 
- EN 60950-1:2006/A11:2009/A1:2010/A12:2011
- EN 301 489-1 V1.9.2
- EN 301-489-17 V2.2.1
- EN 300 328 V1.7.1 

  

Product(s): Graupner/SJ X-4S Transmitter,

              Graupner/SJ GR-4 Receiver
  Item Number(s): No. 33400 , No 33502

  

Graupner/SJ X-4S Transmitter

  

FCC ID: SNL-16005900

  

Graupner/SJ GR-4 Receiver

  

FCC ID: SNL-16005600

(2)

 Conformite Europeenne

(3)

 

FCC Information

 

  ◎ The Guide for the related Countries’ Certifications

4. ALARM EX-VOLT
Selectable auto, 2.0V~24.0V (Default value: Auto)
Detectable from 1.0V to 25.5V (LiPo 4 cell=max 25.2V)

In “Auto” selection, Low voltage warning alarm is activated at 70% 
of detected voltage when power is on.

5. ALARM EX-TEMP
Connect Temperature Sensor to Port 4 (T/V Connecter).
Adjustable from 50℃ to 150℃ (Default value: 100℃)

※ If you have a transmitter that does not have the feature setup for 
temperature, the temperature is fixed at a specific value.

 •  

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is 
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including 
interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party 
responsible for compliance could void the user‘s authority to oper-
ate the equipment.

0678

Summary of Contents for X-4S HoTT SJ

















Reviews: