GRAUPNER 6478 Page 52 Operating Manual Download

Page: 52 / 55

Page

52/55

14. ERROR MESSAGE SCREEN

The error will be displayed on the LCDisplay.

[ INPUT VOLTAGE ]

  * The present input
     voltage  is _0.00V.
  * Please check the
   input voltage.
  * The input voltage

must be 11-15V.

[ NO BATTERY ]

  * A battery is not
   connected to  the
   output
  * Please connect the
    battery  to  the
   output then
   restart  !

[ REVERSE POLARITY ]

  * A battery is
  connected to the
  output in reverse !
  *  Please  correctly
  connect the battery

to the output.

[ OPEN CIRCUIT ]

  * A battery is
   disconnected  during
    an  operation.
  *  Please  reconnect
    the  battery  and

restart!

[ SHORT-CIRCUITED ]

  *  Output  short-
   circuited.
  *  Please  check  the
    output.

[LOW OUTPUT VOLTAGE ]

  * Output voltage is
    lower  than  the
   selected  cells or
   voltages
  * Please  select
   proper cells  or
   voltages

[HIGH OUTPUT VOLTAGE]

  * Output voltage is
   higher than the
   selected  cells or
   voltages
  *  Please  select
    proper  cells  or
    voltages

[TEMPERATURE SENSOR ]

  * A temperature
   sensor  is  connected
   in  reverse  or  is
   defective.

[ BAT. TEMP TOO LOW ]

* Battery temp is too
  low to be operated!

  OUTPUT        _0.000V
  BATT TEMP   __0.0°F

[ BAT. TEMP TOO HIGH]

* Battery temp is too
   high to be operated!

  OUTPUT        _0.000V
  BATT TEMP   __0.0°F

[ INTERNAL TEMP ]

  * Internal temp is
  too hot !
  * Contact Hobby
  Services  if this
  message appears

often.

[DATA COMMUNICATION ]

  * Something is wrong
   with  the  internal
   circuit.
  * Contact Hobby
     Services

[ BAL.VOLTAGE HIGH ]

  * Balancer  cells
   voltage  is too
    high  !!
   over  cell is  [0]

  [   LINK  COMMAND    ]
  * Link order failed !
  Error occured in the

counterpart channel !

[ CONNECTION ]

  * selected cells and
   cells  connected  to
   the  balancing  port
   are  different  !
  * Please recheck and

restart !

[ BAL.VOLTAGE LOW ]

  * Balancer  cells
    voltage  is  too
   low  !!
   low cell is  [0]

[ CALIRATION DATA ]

  *Either  calibration
   data  or  internal
   circuit  might  have
   been  damaged.

[ NO SENSOR ]

  * A temp-sensor is
  not connected to the
  port
  * Please connect the
  temp-sensor  to  the

port then restart !

[MOTOR OVER CURRENT ]

* Please reconnect
the motor and

restart!

[ MOTOR FUNCTION ]

  * Can not start the
  motor  function,
  because other Output
  is  used !
  * Please stop other
  Output  function  to
  start the motor !

Summary of Contents for 6478
























































Search results

Summary of Contents for 6478

Reviews:

Related manuals for 6478

Brands by name

Popular brands

GRAUPNER 6478, Operating Manual

Search results

Summary of Contents for 6478

Reviews:

Related manuals for 6478

Brands by name

Popular brands