GRASS VALLEY K2 SOLO - Quick Start Manual Download Page 40

Page: 40 / 108

Comments

Version

Product

Media assets can be transferred
to/from a Profile XP system but
cannot be browsed.

5.4.8 or higher

Profile XP Media Platform

Check with your Grass Valley
representative for the specific
version.

5.2.x

NetCentral

—

1.4.0.460 and higher

SiteConfig application

—

2.1.1

UIM

—

7.1.1 and higher

K2 TimeDelay

Check with your Grass Valley
representative for version
availability

4.0.3

K2 InSync

On the Avid Editor install the
K2AvidIngest module and on the
device that runs the Avid
Transfer Manager/Interplay
Engine install the K2AvidDhm
module.

7.0.0

K2 Avid plug-in

—

2.0

K2 FCP Connect

—

7.1.0.273

K2-Aurora FTP

3x and 2x frame rates supported.
Requires AppCenter Elite
license.

—

Grass Valley LDK8300 Super
SloMo Camera

2x frame rate. Requires
AppCenter Elite license.

—

Grass Valley LDK8000
SportElite HD Super SloMo
Camera

3x frame rate only; 2x is not
supported. Requires AppCenter
Elite license.

—

Sony 3300 Super SloMo
Camera

—

6.0.2

Edius

Check with your Grass Valley
representative for version
availability.

—

ClipStore

K2 Version 7.3.8 Release Notes & Upgrade Instructions

23 November 2010

Version compatibility

Summary of Contents for K2 SOLO -













































































































Search results

Summary of Contents for K2 SOLO -

Reviews:

Related manuals for K2 SOLO -

Brands by name

Popular brands

GRASS VALLEY K2 SOLO -, Quick Start Manual

Search results

Summary of Contents for K2 SOLO -

Reviews:

Related manuals for K2 SOLO -

Brands by name

Popular brands