background image

7

the gate operator requires a level concrete pad to mount on.  even if the driveway is sloping the 

concrete pad for the operator 

must be leVel!.

 the concrete pad should be no less than 100mm 

thick and after concrete is poured must be given a week or so to harden before the operator is 

installed.

if the gate operator power is to be hard wired it’s a good idea to place a piece of conduit into the 

concrete pad, during installation, for the power cabling later on. 

automatiC operator fittinG requirements

driveway

gate

operator

front fence/wall

concrete footing and pad

concrete

pad

400mm

concrete pad 

400mm

gate

guide

post if used

conduit for power cable to 

come out of concrete pad here 

if power is hardwired.

250mm

200mm

extra gate length 

for automatic 

operator

300mm

plan view

lawn or garden

driveway

extra gate 

length for 

automatic 

operator

need only be the 

bottom rail

concrete pad must be level 

even if gate track isn’t

gate

gate track and footing must 

be straight but can be on a 

gentle slope

front view

driveway

lawn or garden

concrete pad must be well 

drained and not ever be sitting 

in water even after heavy rain

Summary of Contents for SD series



































Reviews: