Grant's Automation IPI-101 Installation Manual Download

Page: 5 / 24

Page 5

Wired Application Diagram

Internet

3G/4G

WiFi to

50m

IPI-101

Home or Office

Router

Smartphone

with App

Smartphone

with App

Tablet with App

and/or

Automatic Gate

Operator

Pedestrian

Gate Electric

Lock

Notes:

IPI-101 is Powered either from an Automatic Gate Operator if used and has 12VDC available, Power Adaptor or through

the Cat 5 Cable from a PoE enabled Router or Switch. PoE means “Power over Ethanet” where the router or switch in-

jects power into the Ethernet Cable so no extra power cable is needed although this cannot be used to power an electric

lock and can go to a maximum or 30m. A Power Adaptor or 12VDC from a gate motor must be used if an electric lock

is required.

If the Cat 5 Cable is to go in the ground it should be a special type that is suitable to go in the ground, that is it has a

tough polythene sheath and is filled with gel to protact it from moisture penatration.

To run 12VDC over a long distance (100m) for an electric lock would require a very thick cable, it would be more eco-

nomic to use a lighter weight cable with a 24VDC unregulated power adaptor at the house or where ever power is avail-

able and 12VDC voltage regulator at the gate that will compensate for any voltage drop.

Cat 5 Cable up to 100m

4core

2core

and/or

Optional Indoor

Monitor Station

Outdoor Camera Station

Power Adaptor

or PoE

Cat 5 Cable up to 100m

or 30m with PoE

Summary of Contents for IPI-101

























Search results

Summary of Contents for IPI-101

Reviews:

Related manuals for IPI-101

Brands by name

Popular brands

Grant's Automation IPI-101, Installation Manual

Search results

Summary of Contents for IPI-101

Reviews:

Related manuals for IPI-101

Brands by name

Popular brands