background image

Setup

3A1602H

19

Fill Wet-cups

Keep the felt washers in the pump wet-cups saturated 
with Graco ISO pump oil, Part No. 217374. The lubricant 
creates a barrier between the ISO and the atmosphere.

Fill wet-cups through the slots in the plate, or remove a 
screw and swing the plate to the side.

Install Pail Heaters

If the material viscosity at room temperature is greater 
than 2000 centipoise the pump may not siphon feed 
on-ratio. Purchase and install the optional flexible pail 
heaters so the material can be warmed, resulting in a 
lower viscosity and enabling the pump to properly 
siphon feed. See 

Accessories

 on page 55. 

Install and operate according to the included pail heater 
manufacturer’s installation manual.

Recirculate Material

The standard system circulates material from the fluid 
manifold back to the supply container. To circulate 
material from the gun back to the material supply con-
tainer, purchase and install Hose Recirculation Kit 
24M654. See 

Install Optional Recirculation Kit

 on 

page 15. 

1.

Insert inlet tubes into pails. See 

Connect Fluid Inlet 

Tubes

, page 21.

2.

Set function knob to Stop/Park. 

3.

Plug in power cord.

4.

Turn on power. 

5.

Set the Recirc/Spray valves to Recirc. 

The pump rod and connecting rod move during 
operation. Moving parts can cause serious injury 
such as pinching or amputation. Keep hands and 
fingers away from the wet-cup during operation. Shut 
off power before filling the wet-cup.

F

IG

. 11: Fill Wet Cup

Follow all warnings and instructions from both the 
fluid manufacturer technical data sheet and the pail 
heater installation manual.

Slots

TI17124a

F

IG

. 12

F

IG

. 13

F

IG

. 14

+

-

TI17127b

I

O

I

O

TI17134a

TI17133a

Summary of Contents for Reactor E-8p 3A1602H



























































Reviews: