background image

12

DISPLACEMENT PUMP SERVICE

20. Refer to the illustration in Fig 5 for your displacement

pump (217–201 or 220–449). Install the gland/pack-

ing stack (160**) on the piston valve (112) as follows,

with the lips of the v–packings facing up.

For Model 217–201  Displacement  Pump:

 Slide

the gland/packing stack supplied in Repair Kit

222–101 down onto the piston valve (1 12). 

Do not

disassemble the packing stack,

 

and be sure the

lips of the packings are facing up. Install the backup

washer (131) on top of the gland/packing stack.

For Model 220–449  Displacement  Pump:

 Slide

the gland/packing stack supplied in Repair Kit

221–156 down onto the piston valve (1 12). 

Do not

disassemble the packing stack,

 

and be sure the

lips of the packings are facing up.

21. Install the piston ball (132) in the piston valve housing

(110). Apply medium grade thread sealant to the

threads of the piston valve (112) and housing (110).

Screw the piston valve into the piston valve housing,

torquing to 81–102 N.m (60–76 ft–lb). Screw the pis-

ton rod (122) into the piston valve, aligning the holes.

Insert the cotter pin (126**).

22. Place the pump housing (109) in the vise. Install the

new o–rings (125**) on the pump cylinder (111). Lu-

bricate the cylinder and slide it into the pump housing

as far as possible.

NOTE:

In Model 220–449 Displacement Pump, install

the pump cylinder so the tapered end faces the

bottom of the pump.

23. Slide the rod guide (113) onto the piston rod (122),

with the flat side facing down.

24. Install the displacement rod assembly through the

bottom of the pump, guiding it carefully through the

throat packings.

Fig 5

Model 217–201

Model 220–449

PISTON PACKINGS

NOTE: LIPS OF V–PACKINGS

MUST FACE UP

131

112

110

110

112

160**

PISTON
GLAND/
PACKING
STACK

160**

PISTON
GLAND/
PACKING
STACK

**126

132

122

122

**126

132

Summary of Contents for Power-Flo Series





























Reviews: