background image

WARNING

FIRE AND EXPLOSION HAZARD

Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.

Ground the equipment. Refer to Grounding on page 4.

If there is any static sparking or you feel an electric shock while using this equipment, stop dis-
pensing immediately.
 Do not use the equipment until you identify and correct the problem.

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being dispensed.

Keep the dispense area free of debris, including solvent, rags, and gasoline.

Electrically disconnect all equipment in the dispense area.

Extinguish all open flames or pilot lights in the dispense area.

Do not smoke in the dispense area.

Do not turn on or off any light switch in the dispense area while operating or if fumes are present.

Do not operate a gasoline engine in the dispense area.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.

Know the specific hazards of the fluid you are using.

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.

Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.

MOVING PARTS HAZARD

Moving parts, such as the air motor piston, can pinch or amputate your fingers.

Keep clear of all moving parts when starting or operating the pump.

Before servicing the equipment, follow the Pressure Relief Procedure on page 6 to prevent the
equipment from starting unexpectedly.

Summary of Contents for Monark 207550
















Reviews: