background image

Warnings

306817N

5

FIRE AND EXPLOSION HAZARD

Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and 
result in a fire or explosion and serious injury.

Ground the equipment and the object being sprayed. See Grounding

If there is any static sparking or you feel an electric shock while using this equipment, stop spraying 
immediately. Do not use the equipment until you identify and correct the problem.

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being 
sprayed.

Keep the spray area free of debris, including solvent, rags, and gasoline.

Before operating this equipment, electrically disconnect all equipment in the spray area.

Before operating this equipment, extinguish all open flames or pilot lights in the spray area.

Do not smoke in the spray area.

Do not turn on or off any light switch in the spray area while spraying or while operating if fumes are 
present.

Do not operate a gasoline engine in the spray area.

TOXIC FLUID OR FUMES HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, 
inhaled, or swallowed.

Know the specific hazards of the fluid you are using.

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, 
state and national guidelines.

Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and 
solvent manufacturer.

WARNING

Summary of Contents for Hydra-Clean 206-515

















Reviews: