background image

Warnings

306817N

3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The 
exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. 
When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. 
Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this 
manual where applicable.

WARNING

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

Use this pump only for pumping water and water--diluted cleaning solutions in a pressure washing 
system. Never use the pump for paint or any other coatings. Any misapplication of the pump may 
cause dangerous operating conditions which can result in serious injury and substantial property 
damage.

This equipment is for professional use only.

Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.

Do not alter or modify this equipment. Use only Graco parts and accessories.

Check equipment daily. Repair or replace worn or damaged parts immediately.

Do not exceed the maximum working pressure stated on the equipment or in the Technical Data for 
your equipment. Do not exceed the maximum working pressure of the lowest rated component in 
your system.

Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical 
Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

Handle hoses carefully. Do not pull on hoses to move equipment.

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose 
Graco hoses to temperatures above 66°C (150°F) or below -40°C (-40°F).

Wear hearing protection when operating this equipment.

Do not move or lift pressurized equipment.

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

Summary of Contents for Hydra-Clean 206-515

















Reviews: