background image

Supply Unit Component Identification

3A8217A

13

Integrated Air Controls (AG)

The integrated air controls include:

Main Air Slider Valve (BA): 

turns the air on and off 

to the iQ Ram Supply Unit. When closed, the valve 
relieves all air pressure downstream.

Ram Air Regulator (BB):

 controls the Ram Assem

-

bly up and down pressure and the blowoff pressure.

Ram Director Valve (BC): 

controls the Ram 

Assembly direction.

Exhaust Port with Muffler (BD)

Blowoff Button (BE):

 turns the air on and off to 

push the Platen (AD) out of an empty drum.

Air Line Accessories

See F

IG

. 3.

Air Line Drain Valve (AS) (not supplied): 

removes 

condensed water from air line.

Air Line Filter (AT) (not supplied):

 removes harm

-

ful dirt and moisture from the compressed air sup

-

ply.

Second Bleed-type Air Valve (AU) (required) (not 
supplied):

 isolates the Air Line accessories for ser

-

vicing. Locate upstream from all other Air Line 
accessories.

F

IG

. 5. Integrated Air Controls

BA

BB

BC

BE

BD

BD

1/4 NPT
Plug

Summary of Contents for E-flo iQ 26B543

















































































Reviews: