manualshive.com logo in svg

Graco CGM 25B127, Instructions - Parts Manual

Share
Download
Graco CGM 25B127 Instructions - Parts Manual Download Page 28

Appendix B - Data Exchanged 

28

3A6338B

Integration System Status

Integration System Status is a boolean that shows the 
status of the Integration System I/O pin. The following 
values correspond to the different states of the 
Integration System Status boolean.

Integration Analog Flow Rate Enabled

Integration Analog Flow Rate Enabled is a boolean that 
can enable usage of the Integration Analog Flow Rate 
I/O pin. The following values correspond to the different 
states of the Integration Analog Flow Rate Enabled 
boolean.

Integration Analog Flow Rate Status

Integration Analog Flow Rate Status is an integer used 
to define the voltage on the Analog Flow Rate I/O pin.

NOTE:

 This integer can only be read by the PLC.

Integration Sequence Selected Enabled

Integration Sequence Selected Enabled is a boolean 
that can enable usage of the Integration Sequence 
Selected I/O pins on the ADM. The following values 
correspond to the different states of the Sequence 
Selected Enabled boolean.

Integration Sequence Selected Status

Integration Sequence Selected Status is an integer 
used to define the active sequence on the EFR by using 
I/O pins on the ADM as bits. When read, the integer 
results in the Active Sequence in the EFR system.

Example

: If the integer has a value of 2, the Active 

Sequence is 2.

NOTE: 

This integer can only be read by the PLC.

Red Pump Cycles

Red Pump Cycles is an integer used to define the 
number of times the red pump has cycled. This can be 
reset by sending a value zero from the PLC over the 
Data Exchange.

Red Pump Lifetime Cycles

Red Pump Lifetime Cycles is an integer used to define 
the number of times the pump has cycled during its 
lifetime.

NOTE: 

This integer can only be read by the PLC.

Blue Pump Cycles

Blue Pump Cycles is an integer used to define the 
number of times the blue pump has cycled. This can be 
reset by sending a value zero from the PLC over the 
Data Exchange.

Blue Pump Lifetime Cycles

Blue Pump Lifetime Cycles is an integer used to define 
the number of times the pump has cycled during its 
lifetime.

NOTE: 

This integer can only be read by the PLC.

Dispense Valve Cycles

Dispense Valve Cycles is an integer used to define the 
number of times the dispense valve has opened. This 
can be reset by sending a value zero from the PLC over 
the Data Exchange.

Dispense Valve Lifetime Cycles

Dispense Valve Lifetime Cycles is an integer used to 
define the number of times the dispense valve has 
opened during its lifetime.

NOTE:

 This integer can only be read by the PLC.

Value

Integration System 

Status State

0

Not  Active

1

Active

Value

Integration Analog Flow 

Rate Enabled State

0

Not Enabled

1

Enabled

Value

Integration Sequence 

Selected Enabled State

0

Not Enabled

1

Enabled

Summary of Contents for CGM 25B127



































Reviews:

No comments

Brands by name

Popular brands

Load more brands