manualshive.com logo in svg

Graco CGM 25B127, Instructions - Parts Manual

Share
Download
Graco CGM 25B127 Instructions - Parts Manual Download Page 26

Appendix B - Data Exchanged 

26

3A6338B

Below is a list of explanations of each individual Data 
Exchange Element.

Dispense Mode

Dispense Mode tells the EFR system whether the 
system is in weight or volume mode. The following 
values correspond to the various dispense modes 
offered by the EFR.

ADM Rate Units

ADM Rate Units tells the EFR system what units the 
rate will be displayed in on the ADM. The following 
values correspond to the various rate units the EFR 
ADM offers.

ADM Pressure Units

ADM Pressure Units tells the EFR system what units the 
pressure will be displayed in on the ADM. The following 
values correspond to the various pressure units the EFR 
ADM offers.

Pressure Imbalance Alarm Enabled

Pressure Imbalance Alarm Enabled is a boolean that 
can enable or disable the ability to view pressure 
imbalances between the red pump and the blue pump. 
The following values correspond to the different states 
the Pressure Imbalance Alarm boolean can be set to.

Pressure Imbalance Alarm Level

Pressure Imbalance Alarm Level is an integer used to 
trigger the pressure imbalance alarm.

Red Pump Size

Red Pump Size is an integer used to define the size of 
the red z pump.

Blue Pump Size

Blue Pump Size is an integer used to define the size of 
the blue z pump.

Red Specific Gravity

Red Specific Gravity is an integer used to define the 
specific gravity of the material in the red z pump.

Blue Specific Gravity

Blue Specific Gravity is an integer used to define the 
specific gravity of the material in the blue z pump.

Gel Timer Enabled

Gel Timer Enabled is a boolean that can enable or 
disable the Gel Timer feature. The following values 
correspond to the different states the Gel Timer boolean 
can be set to.

Gel Timer Idle Period

Gel Timer Idle Period is an integer used to define the 
idle state of the gel timer before the gel timer causes a 
dispense.

Gel Timer Alarm

Gel Timer Alarm is an integer used to define the alarm 
state of the gel timer.

Gel Timer Repeat Unit

Gel Timer Repeat Unit is an integer used to define the 
amount of material dispensed for the gel timer shot.

Value

Dispense Mode State

0

Weight Mode

1

Volume Mode

Value

Rate Units State

0

Per Minute

1

Per  Second

2

Per  Hour

Value

Pressure Units State

0

PSI

1

Bar

Value

Pressure Imbalance 

Alarm State

0

Not Enabled

1

Enabled

Value

Gel Timer Enabled State

0

Not Enabled

1

Enabled

Summary of Contents for CGM 25B127



































Reviews:

No comments

Brands by name

Popular brands

Load more brands