Graco Bulldog Hydra-Cat 231836 Instructions And Parts List Download Page 41

Page: 41 / 46

308225

Accessories

Parts for Installing Optional Solvent Pump

Ref.
No.

Part No.

Description

Qty.

301

151519

NIPPLE, reducing, 1/4–19 nptm
x 1/8–27 nptm

302

111913

COUPLING, hose, 1/4–18
npsm, with spring guard, stain-
less steel

303

061132

HOSE, nylon 1/4” ID x 36” long

304

206264

VALVE, needle, 1/4–18 npt (m)

305

158841

ADAPTER, 1/4–18 unc (f) x
3/8–18 npt (m), carbon steel

306

217523

10:1 RATIO MONARK PUMP,
for heavy viscosity system

208470

5:1 RATIO MONARK PUMP for
light viscosity system

307

157350

ADAPTER, 3/8–18 npt x 1/4–18
npt (mbe)

308

155541

SWIVEL UNION, 90

, 1/4 npt

(f x m)

309

as needed

FLUID HOSE

310

207365

BRACKET, mounting

311

241037

BALL VALVE

312

207484

SUCTION TUBE ASSEMBLY,
3/4 npt

313

100101

SCREW, hex cap head, 3/8–16
unc (2a) x 1”

314

100133

LOCK WASHER, 3/8”

315

100307

NUT, hex, 3/8–16 unc (2b)

316

100132

WASHER, flat, 7/16”

309

310

312

308

307

305

304

314

313

301

Ref 5

311

306

316
315

301

302,303

02902

Miscellaneous Accessories

Nitrogen Regulator Kit, 207638

Maintains a nitrogen head on the supply drum to
protect materials from moisture. Kit includes two 6’ x
1/4” (1.8 m x 6 mm ) hoses, control box with gauge,
regulator, and relief valve.
Inlet: 1/4” npt(m). Outlet: 3/4: npt(m).

Graco Throat Seal Liquid

Non-evaporating liquid for wet-cup

206995

0.95 liter (1 quart)

206996

3.8 liter (1 gallon)

ISO Pump Oil

A highly refined, special purpose throat seal lubricant
the minimal reaction with Isocyanates.

217374

16 ounce (0.13 liter) container

218656

4 gallon (18.14 liter) container

Grounding Wire and Clamp, 222011

7.6 m (25 ft) long,
1.5 mm

(12 gauge)

Summary of Contents for Bulldog Hydra-Cat 231836















































Search results

Summary of Contents for Bulldog Hydra-Cat 231836

Reviews:

Related manuals for Bulldog Hydra-Cat 231836

Brands by name

Popular brands

Graco Bulldog Hydra-Cat 231836, Instructions And Parts List

Search results

Summary of Contents for Bulldog Hydra-Cat 231836

Reviews:

Related manuals for Bulldog Hydra-Cat 231836

Brands by name

Popular brands