Graco Bulldog Hydra-Cat 231836 Instructions And Parts List Download Page 42

Page: 42 / 46

308225

Accessories

Air Control Accessories

Bleed-Type Master Air Valve

300 psi (2.1 MPa, 21 bar) Maximum Working Pressure

Relieves air trapped in the air line between the pump
air inlet and this valve when closed.

107141

3/4 npt(m) inlet x 3/4 npt(f) outlet

107142

1/2 npt(m) inlet x 1/2 npt(f) outlet

Air Line Filter 106149

250 psi (1.7 MPa, 17 bar) Maximum
Working Pressure

Filters harmful dirt and moisture from
the compressed air supply.
1/2 npt(f) inlet and outlet.
See instruction manual 308169.

Air Line Lubricator 214848

250 psi (1.7 MPa, 17 bar) Maximum Working Pressure

Provides automatic lubrication for the air motor.
0.48 liter (16 oz) bowl capacity.
1/2 npt(f) inlet and outlet.
See instruction manual 308169.

Pump Runaway Valve 224040

120 psi (0.8 MPa, 8 bar) Maximum Working Pressure

3/4 npt(f) inlet and outlet.
Includes optional 90

3/4 npsm swivel outlet fitting.
See instruction manual
308201.

Shuts off air supply to the pump if the pump acceler-
ates beyond the pre-adjusted setting due to an empty
supply container, interrupted fluid supply to the
pump, or excessive cavitation.

Air Regulator 206197

300 psi (2.1 MPa, 21 bar) Maximum Working Pressure

Controls air pressure to feed, sol-
vent, or proportioning pumps.
1/2 npt inlets and outlets, with (2)
1/4 npt pressure gauge outlets.

Fluid Control Accessories

Fluid Filter

5000 psi (34 MPa, 345 bar) Maximum Working Pressure

60 mesh (250 micron) screen.

Model 218029

Carbon steel bowl and support

Model 223160

Stainless steel bowl and polyeth-
ylene support

Fluid Shutoff Valve

5000 psi (34 MPa, 345 bar) Maximum Working Pressure

Model 235992

stainless steel with PTFE seals
1/4 x 3/8 nps (mbe)

Model 223960

carbon steel with PTFE seals
3/8 npt (mbe)

Model 214037

carbon steel with PTFE seals
1/4 npt (mbe)

Static Mixing Units

3000 psi (21 MPa, 207 bar) Maximum Working Pressure

These units consist of a tube with helical interior
elements which thoroughly blend base and catalyst
materials into the proper mix.

Model 500639

14” (356 mm) long, 5/16” (8 mm) ID, 27 Elements
3/8 npt

order fittings separately

Model 500586

25” (635 mm) long, 0.44” (11 mm) ID, 32 Elements
1/2 npt

order fittings separately

Model 502028

29” (736 mm) long, 0.8” (20 mm) ID, 24 Elements
3/4 npt

Model 945917

25” (635 mm) long, 2–1/2” (64 mm) OD, 10 Elements
1” npt (m x f)

Summary of Contents for Bulldog Hydra-Cat 231836















































Search results

Summary of Contents for Bulldog Hydra-Cat 231836

Reviews:

Related manuals for Bulldog Hydra-Cat 231836

Brands by name

Popular brands

Graco Bulldog Hydra-Cat 231836, Instructions And Parts List

Search results

Summary of Contents for Bulldog Hydra-Cat 231836

Reviews:

Related manuals for Bulldog Hydra-Cat 231836

Brands by name

Popular brands