background image

16

307132

Operation

Proportioning Pump Chart

Displacement pump combinations for mix ratio, pres-
sure ratio and volume per cycle for each model.

CAUTION

With three displacement pump models, the outer two
displacement pumps must be identical models to
balance forces and avoid damaging the pumps.

Mix

Part A

Part B

Part A

Pressure
Ratio 
(fluid to air)

Volume per
Cycle
Gallon (liter)

Fluid Pressure Developed
psi (MPa, bar)
at incoming air pressure of
psi (MPa, bar)

1:1

222012

222012

None

34:1*

0.046 (0.17)

2500 (17, 170)
74 (0.5, 5.2)

1-1/4:1 222019

222015

222019

38:1*

0.034 (0.13)

2500 (17, 170)
66 (0.4, 4.5)

1-1/2:1 222019

222017

222019

41:1*

0.038 (0.14)

2500 (17, 170)
61 (0.4, 4.2)

2:1

222012

222012

222012

23:1

0.068 (0.26)

2300 (16, 161)
100 (0.7, 7)

2-1/2:1 222012

222015

222012

24:1

0.064 (0.24)

2400 (16.8, 168)
100 (0.7, 7)

3:1

222012

222017

222012

25:1

0.061 (0.23)

2500 (17, 170)
100 (0.7, 7)

4:1

222012

222019

222012

27:1

0.057 (0.22)

2500 (17, 170)
93 (0.6, 6.4)

* Exceeds the pressure ratiing of the pumps.

Relief Valve Selection Table

To select the appropriate relief valve:

1.

Determine the Maximum Pump Fluid Pressure of
your system.

2.

Verify that all system components meet or exceed
the pressure ratings of the pressure relief valve
that you have selected.

3.

Select the lowest pressure relief valve with a maxi-
mum working pressure that exceeds the Maximum
Pump Fluid Pressure.

Part
Number

Working Pressure
Range psi (MPa, bar)

Cracking Pressure
Range psi (MPa, bar)

Minimum

Maximum

Minimum

Maximum

237060

475 
(3.3, 33)

575 
(4, 40)

710 
(4.9, 49)

860 
(5.9, 59)

237061

950 
(6.6, 66)

1150 
(7.9, 79)

1425 
(9.8, 98)

1725
(11.9,
119)

237112

1400 
(9.7, 97)

1800
(12.4,
124)

2140
(14.8,
148)

2590
(17.9,
179)

237062

1800
(12.4,
124)

2300
(15.9,
159)

2850
(19.7,
197)

3450
(23.8,
238)

Summary of Contents for BULLDOG HYDRA-CAT 208958



























Reviews: