Gotting HG 73840ZB Device Description Download Page 22

Page: 22 / 65

Software / Parameter Settings

HG 73840ZB

English, Revision 06, Date: 12.07.2011

Figure 9

Screenshot: Status bits as plaintext

Rating

Function when deleted

Function when set

0x8000

Toggles following each transmitted PDO

0x4000

No track detected

Track detected

0x2000

Track quality good

Track quality bad

0x1000

No barcode

barcode decoded

0x0800

Deviation signal > -Threshold 2 left

Deviation signal < -Threshold 2 left

0x0400

Deviation signal > -Threshold 1 left

Deviation signal < -Threshold 1 left

0x0200

Deviation signal < Threshold 1 right

Deviation signal > Threshold 1 right

0x0100

Deviation signal < Threshold 2 right

Deviation signal > Threshold 2 right

0x0080 *)

Parameter set 1 or 3 active

Parameter set 2 or 4 active

0x0040 *)

Camera 1 active

Camera 2 active

0x0020 *)

Status of the parallel inputs IN1 and IN2 for turning and release of the analog output
according to

0x0010 *)

0x0008

No further track on the right

further track to the right of the current is
found

Table 7

Allocation of status bits

Peak 22359 @ 263 X/mm: 3 S: 4030 Code: 255 SCmin: 0 %

State: 4030 Config: E1C9

2^0: 0 (PARAM_CRC_OK) 1 (CANopen AUTOSTART)

2^1: 0 (PAR_OUT_OK) 0 (CAM_1)

2^2: 0 (NO_TRACK_L_DET) 0 (NO WIDTH_CHECK)

2^3: 0 (NO_TRACK_R_DET) 1 (Black on White P1)

2^4: 1 (TURN_RI) 0 (ANALOG_CLEAR)

2^5: 1 (TURN_LE) 0 (SER/CAN IN)

2^6: 0 (CAM_1) 1 (TURN_RI)

2^7: 0 (PARA_1) 1 (TURN_LE)

2^8: 0 (THR_2_RI) 1 (SERIAL)

2^9: 0 (THR_1_RI) 0 (LO-Byte first)

2^10: 0 (THR_1_LE) 0 (NO EDGE)

2^11: 0 (THR_2_LE) 0 (DEVIATION_OUT)

2^12: 0 (NO CODE) 0 (PARA_SET 1)

2^13: 0 (TRACK_GOOD) 1 (Black on White P2)

2^14: 1 (TRACK DETECT) 1 (Black on White P3)

IN2

IN1

Rating in the Status

Function

0x..0.

>No release of the analog output

0x..1.

Turn right

0x..2.

Turn left

0x..3.

Straight on

Table 6

Coding of input IN1 and IN2

Summary of Contents for HG 73840ZB


































































Search results

Summary of Contents for HG 73840ZB

Reviews:

Related manuals for HG 73840ZB

Brands by name

Popular brands

Gotting HG 73840ZB, Device Description

Search results

Summary of Contents for HG 73840ZB

Reviews:

Related manuals for HG 73840ZB

Brands by name

Popular brands