manualshive.com logo in svg

Gossen MetraWatt PROFITEST PRCD, Operating Instructions Manual, Page: 7 / 16

Share
Download
Gossen MetraWatt PROFITEST PRCD Operating Instructions Manual Download Page 7

GMC-I Messtechnik GmbH

7

3.3

Connecting the PRCD

The respective PRCD must be connected to 
the test adapter for all tests.

Connecting a Single-Phase PRCD 

➭

Insert the earthing contact inlet plug from 
the PRCD into the earthing contact out-
let (4) at the test adapter.

➭

Insert the earthing contact plug (2) from 
the test adapter into the outlet coupling 
socket at the PRCD.

Example of a Single-Phase PRCD

Connecting a 3-Phase PRCD

➭

Insert the CEE inlet plug from the PRCD 
into the CEE outlet (6) at the test 
adapter.

➭

Insert the CEE plug (1) from the test 
adapter into the CEE outlet coupling 
socket at the PRCD.

4

Measurements with the 
PROFITEST MXTRA

In order to perform protective conductor mea-
surements (Rlo) at 

type S PRCDs 

with the 

PROFITEST 

MXTRA

, the test adapter must remain connected 

to the mains.
The test adapter can remain connected to the 
mains for protective conductor measurements 
conducted at PRCDs whose protective conduc-
tor is not switched, as well as for insulation mea-
surements (Rins) with the 

PROFITEST MXTRA

4.1

Measuring Protective Conductor 
Resistance (Rlo)

As opposed to the usual default setting for 
low-resistance measurements, the device 
under test does not have to be discon-
nected from all sources of voltage in this 
case. Depending on the PRCD, the rotary 
selector switches have to be set to the 

ON

 

and the 

1~ ON

 or 

3~ ON

 positions, in order to 

be able to activate the PRCD and switch the 
protective conductor through.

Example of a Single-Phase PRCD

➭

Before performing protective conductor 
measurements, execute an offset mea-
surement to assure that the test 
adapter’s connector contacts are not in-
cluded in the measurement results. 

➭

Insert the respective test plug into the 
appropriate socket at the test adapter to 
this end: 2 to 4 or 1 to 6.

➭

Start the offset measurement at the 

PROFITEST MXTRA

.

➭

Connect the PRCD as described in sec-
tion 3.3.

➭

Connect the 

PROFITEST MXTRA

 test instru-

ment to sockets 9 and 10 via the 2-pole 
measuring adapter.

PROFI

TEST

⏐

P

RCD

Measurement with the PROFITEST MXTRA

Summary of Contents for PROFITEST PRCD

















Reviews:

No comments