manualshive.com logo in svg

Gossen MetraWatt PROFITEST PRCD, Operating Instructions Manual, Page: 12 / 16

Share
Download
Gossen MetraWatt PROFITEST PRCD Operating Instructions Manual Download Page 12

12

GMC-I Messtechnik GmbH

6.3

PRCD-S (3-phase) 

➭

Switch mains power on by 
turning the right-hand rotary 
selector switch to the 

3~ ON

 position.

6.3.1

Simulated Interruption

 

➭

Start with the left-hand rotary se-
lector switch in the first 

ON

 position in the 

green area for single-phase interruption.

➭

Switch through the positions, one after 
the other, in the clockwise direction (ta-
ble from top to bottom).

Conductor Interruption Using a 3-Phase PRCD from Kopp as an Example 

Regarding step 8:

The N LED also lights up due to star connection, although N is interrupted!

Note!

Tripping performance may deviate 
from this example in the case of 
PRCDs from other manufacturers – 
adhere to the manufacturer’s test 
instructions!

St

e

p

Rotary 
Switch 

Test Adapter

PRCD Action

L1 
LED

L2 
LED

L3 
LED

N 
LED

PE 
LED

LED

1

Activate the PRCD.

2

The PRCD is tripped. It must 
not be possible to reactivate it.

3

Activate the PRCD.

4

The PRCD is tripped. It must 
not be possible to reactivate it.

5

Activate the PRCD.

6

The PRCD is tripped. It must 
not be possible to reactivate it.

7

Activate the PRCD.

8

The PRCD is tripped. It must 
not be possible to reactivate it.

9

Activate the PRCD.

10

The PRCD is tripped. It must 
not be possible to reactivate it.

PROFI

TEST

⏐

P

RCD

Fault Simulation

Summary of Contents for PROFITEST PRCD

















Reviews:

No comments