manualshive.com logo in svg

Gossen MetraWatt PROFITEST PRCD, Operating Instructions Manual, Page: 13 / 16

Share
Download
Gossen MetraWatt PROFITEST PRCD Operating Instructions Manual Download Page 13

GMC-I Messtechnik GmbH

13

6.3.2

Simulated Wire Reversal 

➭

Turn the left-hand rotary selector 
switch to the 

L1-N

 position in the green 

area for 3-phase wire reversal.

➭

Switch through the positions, one after 
the other, in the clockwise direction (ta-
ble from top to bottom).

It must not be possible to activate the PRCD 
when any of these faults is simulated.

6.3.3

Simulation of PE to Phase

➭

Set the left-hand rotary selector switch 
to the 

PE-U

EXT

 position.

It must not be possible to activate the PRCD 
when this fault is simulated.

➭

Step 18: see section entitled “Protective 
Conductor Current Measurement” on 
page 9.

St

e

p

Rotary 
Switch 

Test Adapter

PRCD Action

L1 
LED

L2 
LED

L3 
LED

N 
LED

PE 
LED

LED

11

It must not be possible to 
activate the PRCD.

12

It must not be possible to 
activate the PRCD.

13

It must not be possible to 
activate the PRCD.

14

It must not be possible to 
activate the PRCD.

15

It must not be possible to 
activate the PRCD.

16

It must not be possible to 
activate the PRCD.

St

e

p

Rotary 
Switch 

Test Adapter

PRCD Action

L1 
LED

L2 
LED

L3 
LED

N 
LED

PE 
LED

LED

17

It must not be possible to 
activate the PRCD.

PROFI

TEST

⏐

P

RCD

Fault Simulation

Summary of Contents for PROFITEST PRCD

















Reviews:

No comments