Gorilla Playsets Wilderness Gym II 1500JWF Manual Download Page 133

Page: 133 / 174

1 X 5 X 36-3/4"

ROOF BOARD

(5 PER SIDE)

ROOF FINISHER

(1 PER SIDE)

#8 X 1-1/2"

WOOD SCREW

1 X 4 X 36-3/4"

#8 X 1-1/2"

WOOD SCREW

STEP 27: ROOF BOARDS AND ROOF FINISHERS

1: LOCATE TEN 1 X 5 X 36-3/4" ROOF BOARDS. SLIDE THE TONGUE OF THE ROOF BOARD INTO

THE GROOVE OF THE ROOF STARTER. SECURE THE ROOF BOARD TO THE ROOF SUPPORTS WITH

FOUR #8 X 1-1/2" WOOD SCREWS.
2: SLIDE THE NEXT ROOF BOARD TONGUE INTO THE GROOVE OF THE PREVIOUS ROOF BOARD.

SECURE THE ROOF BOARD TO THE ROOF SUPPORTS WITH FOUR #8 X 1-1/2" WOOD SCREWS.
3: REPEAT SUBSTEP 2 FOR THE NEXT 3 ROOF BOARDS.
4: LOCATE A 1 X 4 X 36-3/4" ROOF FINISHER (TONGUE ONLY). INSERT THE TONGUE OF THE

ROOF FINISHER INTO THE GROOVE OF THE LAST ROOF BOARD. SECURE THE ROOF FINISHER TO

THE ROOF SUPPORTS WITH FOUR #8 X 1-1/2" WOOD SCREWS.
5: REPEAT SUBSTEPS 1 THROUGH 4 FOR THE ROOF BOARDS AND ROOF FINISHER ON THE OTHER

SIDE OF THE ROOF.

123

Summary of Contents for Wilderness Gym II 1500JWF















































































































































































Search results

Summary of Contents for Wilderness Gym II 1500JWF

Reviews:

Related manuals for Wilderness Gym II 1500JWF

Brands by name

Popular brands

Gorilla Playsets Wilderness Gym II 1500JWF, Manual

Search results

Summary of Contents for Wilderness Gym II 1500JWF

Reviews:

Related manuals for Wilderness Gym II 1500JWF

Brands by name

Popular brands