Gorilla Playsets Wilderness Gym II 1500JWF Manual Download Page 58

Page: 58 / 174

BOARD

PANEL

BOTTOM

2 X 6

SUPPORT

ANGLE

SUPPORT

2" WOOD

SCREW

3" WOOD

SCREW

3" WOOD

SCREW

2 X 4 X 18"

2 X 4 X 13"

2" WOOD

2-1/2"

WOOD

SCREW

SUPPORT

ANGLE

SHOULD BE FLUSH OR LOWER

DETAIL F

SCALE 1 : 8

SUPPORT

2 X 4 X 13"
SUPPORT

ANGLE

THAN THE DECK SUPPORT.

DECK

2 X 4 X 18"

TOP OF ANGLE SUPPORTS

2 X 6

BOTTOM

PANEL

BOARD

STEP 6B: ANGLE SUPPORTS

1: ONE 2 X 4 X 18" ANGLE SUPPORT IS MOUNTED UNDER THE DECK ON THE LEFT REAR OF

THE PLAY SET TO THE 2 X 6 BOTTOM PANEL BOARD.

THE TOP OF THE ANGLE SUPPORT

SHOULD BE FLUSH OR LOWER THAN THE TOP OF THE DECK SUPPORT.

2: AT THE TOP USE 2-1/2" WOOD SCREWS THROUGH THE ANGLE SUPPORT INTO THE

BOTTOM PANEL BOARD. AT THE BOTTOM USE ONE 2" AND ONE 3" WOOD SCREW TO

FASTEN THE ANGLE SUPPORT TO THE CORNER POST.
3: THREE 2 X 4 X 13" ANGLE SUPPORTS ARE MOUNTED UNDER THE DECK ON THE FRONT

AND REAR OF THE PLAY SET TO THE 2 X 4 DECK SUPPORTS.

THE TOP OF THE ANGLE

SUPPORT SHOULD BE FLUSH OR LOWER THAN THE TOP OF THE DECK SUPPORT.

4: AT THE TOP USE 2-1/2" WOOD SCREWS THROUGH THE DECK SUPPORT INTO THE ANGLE

SUPPORT. AT THE BOTTOM USE ONE 2" AND ONE 3" WOOD SCREW TO FASTEN THE ANGLE

SUPPORT TO THE CORNER POST.

SUPPORT

2 X 4 X 13"
SUPPORT

ANGLE

2 X 4 X 13"

ANGLE

2 X 4 X 13"

ANGLE

SUPPORT

Summary of Contents for Wilderness Gym II 1500JWF















































































































































































Search results

Summary of Contents for Wilderness Gym II 1500JWF

Reviews:

Related manuals for Wilderness Gym II 1500JWF

Brands by name

Popular brands

Gorilla Playsets Wilderness Gym II 1500JWF, Manual

Search results

Summary of Contents for Wilderness Gym II 1500JWF

Reviews:

Related manuals for Wilderness Gym II 1500JWF

Brands by name

Popular brands