Gorilla Playsets Wilderness Gym II 1500JWF Manual Download Page 95

Page: 95 / 174

2" LAG SCREW WITH 1-1/4"

FENDER WASHER

87" MARKS

STEP 38A: ATTACHING THE SLIDE TO THE FORT

1: MEASURE FROM THE BOTTOM OF THE ROPE LADDER SUPPORT UP 87". MAKE A MARK ON THE CORNER POST

AND ON THE SLIDE MOUNT POST.
2: WITH THE HELP OF AN ASSISTANT PLACE THE SLIDE INTO POSITION AND LINE UP THE TOP WITH THE MARKS AT 87".

LOOK TO SEE IF THE FOOTER IS FLAT UPON THE GROUND. ADJUST THE SLIDE UP OR DOWN SLIGHTLY UNTIL THE FOOT

RESTS FLAT UPON THE GROUND.
3: FASTEN THE LOWEST HOLES AS SHOWN BELOW WITH A 2" LAG SCREW A 1-1/4" FENDER WASHER. DO NOT

ATTACH THE BOTTOM RIGHT HOLE OF THE SLIDE ENTRY PLATE AT THIS TIME.
4: WORK YOUR WAY UP THE SIDES

INSTALLING MORE 2" LAG SCREWS

WITH 1-1/4" FENDER WASHERS.
5: NOW GO ALL AROUND THE SLIDE

AND TIGHTEN UP ALL OF THE BOLTS

IF YOU HAVE NOT DONE SO ALREADY.

LEAVE THIS HOLE EMPTY

2" LAG SCREW WITH 1-1/4"

FENDER WASHER

Summary of Contents for Wilderness Gym II 1500JWF















































































































































































Search results

Summary of Contents for Wilderness Gym II 1500JWF

Reviews:

Related manuals for Wilderness Gym II 1500JWF

Brands by name

Popular brands

Gorilla Playsets Wilderness Gym II 1500JWF, Manual

Search results

Summary of Contents for Wilderness Gym II 1500JWF

Reviews:

Related manuals for Wilderness Gym II 1500JWF

Brands by name

Popular brands