background image

CLEANING THE MONITOR

-

Do not use solvents, detergents or cleaning products that contain acids, vinegar or abrasive components.

-

Use a soft damp cloth (not wet) that sheds no

fi

bres.

-

Always wipe the monitor in the same direction, from top to bottom.

-

After cleaning the monitor, remove any moisture with a soft dry cloth that sheds no

fi

bres.

OPTIONAL CONNECTIONS

17

TEKNA PLUS SE MONITOR

Button for receiving calls from the apartment front door:

HZ-

-

The Tekna Plus SE monitor features as standard the ability to receive calls from the apartment front door. This

feature precludes the need to use the bell by positioning a switch between terminals HZ

and

of the monitor

The ringtones vary depending on where the call is made from to enable the user to identify its origin. If a call is made

from the apartment front door during a conversation with the door panel, the handset will emit a number of tones
to indicate so.

Not :

e

Regardless of the volume set for the monitor's ringtones (see page 11) and the night mode function, the

apartment front door call ringtone will always sound at the highest level.

Tekna Plus SE

Continued from the previous page.

Summary of Contents for Tekna Plus SE





















Reviews: