Godex GS550 User Manual Download Page 17

Page: 17 / 140

2 - 1

2. Programming the Interface

Introduction

This chapter describes how to program your system for the desired interface.

Programming the Interface - Plug and Play

Plug and Play bar codes provide instant scanner set up for commonly used
interfaces.

Note: After you scan one of the codes, power cycle the host terminal to have

the interface in effect.

Keyboard Wedge

If you want your system programmed for an IBM PC AT and compatibles key-
board wedge interface with a USA keyboard, scan the bar code below. Key-
board wedge is the default interface.

Note: The following bar code also programs a carriage return (CR) suffix.

IBM PC AT and Compatibles with

CR suffix

Laptop Direct Connect

For most laptops, scanning the

Laptop Direct Connect

bar code allows opera-

tion of the scanner in parallel with the integral keyboard. The following

Laptop

Direct Connect

bar code also programs a carriage return (CR) suffix and turns

on Emulate External Keyboard (page 2-12).

Laptop Direct Connect

with CR suffix

Summary of Contents for GS550













































































































































Search results

Summary of Contents for GS550

Reviews:

Related manuals for GS550

Brands by name

Popular brands

Godex GS550, User Manual

Search results

Summary of Contents for GS550

Reviews:

Related manuals for GS550

Brands by name

Popular brands