Godex GS550 User Manual Download Page 29 | Manualshive

Page: 29 / 140

background image

2 - 13

Default = Off.

Control Character Output On

Keyboard Modifiers

* Control Character Output Off

This modifies special keyboard features, such as CTRL+ ASCII codes and
Turbo Mode.

C ASCII Mode On:

The scanner sends key combinations for ASCII

control characters for values 00-1F.  Windows is the preferred mode.  All key-
board country codes are supported.  DOS mode is a legacy mode, and it does
not support all keyboard country codes.  New users should use the Windows
mode.  Refer to Keyboard Function Relationships, page 7-1 for CTRL+ ASCII
Values.

Windows Mode Prefix/Suffix Off:

The scanner sends key combinations for

ASCII control characters for values 00-1F, but it does not transmit any prefix or
suffix information.

Default = C ASCII Mode Off.

Windows Mode C ASCII

Mode On

* C ASCII Mode Off

DOS Mode C ASCII Mode

On

Windows Mode Prefix/Suffix Off

«
...
27
28
29
30
31
...
»

Summary of Contents for GS550













































































































































Reviews:

No comments

Related manuals for GS550

Brand: Hamlet Pages: 63

Universal 3 in 1 Reader/Writer

Brand: Dazzle Pages: 47

Brand: Stid Pages: 16

PRS-505/LC - Portable Reader System

Brand: Sony Pages: 2

Brand: Sony Pages: 2

PRS-350SC - Reader Pocket Edition&trade

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

PRS-300BC - Reader Pocket Edition

Brand: Sony Pages: 2

PRS-300 - Reader Pocket Edition&trade

Brand: Sony Pages: 2

PRS-300 - Reader Pocket Edition PRS-300LC - Reader Pocket Edition PRS-300

Brand: Sony Pages: 2

PRS-600 - Electronic Book Reader

Brand: Sony Pages: 14

PRS-350 - Reader Pocket Edition&trade

Brand: Sony Pages: 16

PRS-300 User’s Guide

Brand: Sony Pages: 14

Brand: Sony Pages: 60

Brand: Sony Pages: 82

Brand: Sony Pages: 72

Brand: Sony Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands