Godex GS550 User Manual Download Page 36 | Manualshive

Page: 36 / 140

background image

3 - 6

Presentation Mode

Presentation Mode uses ambient light to detect bar codes. The LED dims until
a bar code is presented to the scanner, then the LED brightens to read the
code. If the light level in the room is not high enough, Presentation Mode may
not work properly.

Presentation Mode

Presentation Sensitivity

Presentation Sensitivity is a numeric range that increases or decreases the
scanner's reaction time to bar code presentation. To set the sensitivity,
scan the

Sensitivity

bar code, then scan the degree of sensitivity (from 0-

20) from the inside back cover, and

Save

. 0 is the most sensitive setting,

and 20 is the least sensitive. Default = 1.

Sensitivity

Presentation Centering

Use Presentation Centering to narrow the scanner

’s field of view when it is

in the stand to make sure the scanner reads only those bar codes intended
by the user. For instance, if multiple codes are placed closely together,
Presentation Centering will insure that only the desired codes are read.

Note: To adjust centering when the scanner is hand-held, see

Centering (page 3-10).

If a bar code is not touched by a predefined window, it will not be decoded
or output by the scanner. If Presentation Centering is turned on by scan-
ning

Presentation Centering On

, the scanner only reads codes that pass

through the centering window you specify using the

Top of Presentation

Centering Window, Bottom of Presentation Centering Window, Left

,

and

Right of Presentation Centering Window

bar codes.

«
...
34
35
36
37
38
...
»

Summary of Contents for GS550













































































































































Reviews:

No comments

Related manuals for GS550

Brand: D'Tech Pages: 3

Brand: Cognex Pages: 17

QuickScan QS6500BT

Brand: Datalogic Pages: 16

Brand: Addonics Technologies Pages: 1

Brand: Krüger & Matz Pages: 40

Brand: Motorola Pages: 82

SYMBOL MT2000 Series

Brand: Motorola Pages: 304

Brand: Motorola Pages: 2

Brand: Motorola Pages: 24

Brand: Motorola Pages: 432

Symbol CS3000 Series

Brand: Motorola Pages: 153

Brand: Motorola Pages: 404

Brand: Motorola Pages: 418

Brand: IDTECH Pages: 33

Brand: IDTECK Pages: 20

Brand: IDTECH Pages: 19

Brand: IDTECH Pages: 23

Brand: IDENTEC SOLUTIONS Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands