background image

  IV. Appendix

1.  

Trouble Shooting

PROBLEM              

SOLUTION

Does not display any message 
on the front panel or STB has 
no power. 

- Check the main power cable and check that it is   plugged into a suitable power outlet. 
- Check whether STB is in Standby mode. 

No Picture 

- Ensure that the STB is switched on (see above).
- Check the video output port (SCART) is 

fi

 rmly  connected  to the TV or VCR. 

- Check that you have selected the correct channel or  Video. 
- Output on your TV. 
- Check the brightness level of the TV. 

Poor picture quality 

- See „No Picture“ above. 
- Check the signal level, if this is low then try adjusting  the alignment of your dish. 

No Sound 

- See „No Picture“ above. 
- Check the volume level of the TV and STB. 
- Check the Mute status of the TV and STB.

Remote Control does not 
operate 

- Point remote control directly towards the STB. 
- Check and replace batteries. 

No or Bad Signal 

- Check the LNB - replace LNB if necessary. 
- Check the cable from the LNB. 
- Check the position of the dish-realign dish if necessary. 
- If you are using a DiSEqC 1.0 switch, check that you have connected the LNBs to the     
  correct  connections on the switch. 

Distorted menu screen

Remove power cord or AC reset switch OFF/ON

2.  

Technical Speci

fi

 cation

TUNER

 

1 Input Connector 

F-type, IEC 169-24 IF 

Input Frequency 

950MHz to 2150MHz

IF Loop Throughout 

950MHz to 2150MHz 

Input Level 

-65 dBm ~ -25 dBm 

LNB Power 

13/18VDC / 500mA Max 

DiSEqC Control 

1.0, 1.2 & USALS compatible 

Band Switch 

22KHz Tone; ( 22+/- 4KHz, Amplitude : 0.6 +/- 0.2V) 

Modulation method 

LDPC/BCH(DVB-S2) 8PSK/QPSK: 10~30Msps; DVB-S QPSK 

Symbol Rate 

LDPC/BCH(DVB-S2) 8PSK/QPSK: 10~30Msps; DVB-S QPSK : 1~45Msps 

Viterbi Decoding Rate 

1/2, 2/3, 3/4, 5/6 and 7/8 

Bandwitdth 36MHz 
LDPC/BCH 

Punctured Code, 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10 in DVB-S2

TERRESTRIAL (Option)          

Input Connector 

IEC-Type IEC 169-24, Female 

Input Freq 

VHF 174~230MHz, UHF 470~860MHz 

Guard Internal Mode 

1/32, 1/16,1/8,1/4 Active symbol duration 

Bandwidth 

7MHz/8MHz ( europe ) 

Viterbi Decoding Rate 

1/2,2/3, 3/4,5/6, 7/8 

Reed Solomon Decoding 

FEC 204, 188, T=8 

Demodulation 

OFDM 2K/8K Carrier

19

Summary of Contents for GS 8010






















Reviews: