background image

1

REV.01

INSTALLATION INSTRUCTIONS

PART NO.

PRODUCT SAFETY & LEGAL DISCLAIMER

© 2016 Go Rhino Products. All rights reserved

www.gorhino.com

589 W. Apollo St., Brea, CA 92821          P: 888 427 4466

IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO 
MAY CAUSE PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY. 

Review the product package and contents prior to beginning the installation. Take care when 
opening the packaging and removing items. If a return is needed you will want to return the product in 
its original packaging if possible.

This instruction guide is provided as a GENERAL installation guide, some vehicles vary dimensionally 
and may require additional steps. 

Test fit the product on the vehicle prior to any third party modifications and or finishing. The 
manufacturer and/or distributors do not accept responsibility for third party charges, labor and or 
third part replacement modifications. Some modifications may void the factory warranty.

Exercise due-diligence when installing this product. The manufacturer and distributors of this product 
do not accept any responsibility for vehicle damage or personal injury resulting from the installation of 
this product. Careless installation and operation can result in serious injury or equipment damage.

This product is for general off-road use. All liability for installation and use rests with the 
owner/operator.

INSTALLER: Once installation is complete, please return this guide along with other documentation 
included in this product back to the consumer for future reference. The manufacturer/distributors of 
this product do not guarantee this particular version will be available at a later date.

PRODUCT DESCRIPTION:

5934048T

5934058T

5934068T

SRM400  MODULAR  ROOF  RACK

V

. 3

  0

5.

13

.2

01

6

Summary of Contents for 5934048T

















Reviews: