GLOBBER FLOW FOLDABLE 125, Owner'S Manual

Page: 6 / 68

6
ENGLISH
Keep the instructions for future.
NF-EN-14619
READ THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER BEFORE USING.
MAXIMUM WEIGHT: 100 KG
Warnings
- The Scooter is reserved for adolescents and adults. It is not a toy, but sports equipment for
physical training, it is not intended for use in extreme sports such as jumping, ollie ramps, etc. This
product should never be used at a skate park for an “aggressive” use (challenging skateboarding
moves, etc.).
- Use with caution on a flat, clean, dry surface and, if possible, away from other users, and obey
the road safety rules.
- Check local laws regarding scooter use, respect all the traffic rules and signs. Stay away from
other pedestrians or users on public roads.
- Best when used on a flat, dry surface free of gravel and grease. Avoid bumps and drainage grates
that might cause an accident.
- Warning! Protective equipment consisting of wrist protectors, gloves, knee pads, helmets and
elbow pads should be worn.
Using the scooter
• Before and after each use : To prevent pinched fingers, carefully follow the instructions of
unfolding and folding. Make sure that the locking mechanisms are securely locked:
- Check the height of the steering system and make sure that the nuts are tightened and the
handlebars and front wheel are perpendicular.
- Check all of the connection elements: the brake, the quick release system of the steering column
and the wheel axles must be correctly adjusted and must not be damaged
- Also check the tire wear.
• Braking:
- A brake is located at the rear, when necessary, press down on it to slow down. Press down
gradually to prevent skidding or loss of stability. The metal brake may heat up after multiple uses.
Avoid touching it during and after use.
- If model with the handlebar brake: a right brake handle to slow the back wheel. When using, keep
riding the scooter with both hands.
Assembling the product
- The folding and unfolding operations of the scooter are to be done by a single person.
- During these operations, be careful you do not get your fingers stuck in the hinge and
locking system.
- Make sure that the locking devices are properly engaged.
1 - Unfold the scooter
D1 : Unpack the folded-up scooter from its box.
D2 : Hold the scooter, one hand is holding the handle and the other hand pulls away the eyelet
trigger until the lock clicks open. Unfold the handle and front wheel upwards until the automatic lock
secures the T-bar handle in upright position.
D3 : Pull out both parts of the T-bar handle from the double clips. Press in the spring loaded buttons
and insert both into the tubes of the T-bar. Wiggle and turn a bit until their spring loaded locking
buttons align with the holes and fix the whole steering bar assembly in place.
Warning! Risk of injury by pinching!
Do not insert your fingers into the shaded area indicated
2 - Adjust the handle bar
D4
: Open the fixing lug. Then press down the spring loaded locking button and pull the handlebar
up or push it down with the other hand.
Choose the suitable locking hole and make sure the spring loaded locking pin snaps securely in
place. The adjustable T-bar handle can be adapted in height to suit the rider.
Three different positions are available.
Lock the fixing lug tight and securely when you have finished adjusting the height.
Self-standing mode
D5 : Pull the eyelet trigger slightly up to release the lock and fold back the T-bar just a tad.
Release the eyelet trigger when the deck touches the ground. The scooter is now in self-standing
mode. You can now leave the scooter standing in that position. You can park your scooter upright
on any flat surface.
3 - Fold up the scooter
D6 : Pull the eyelet trigger up to unlock the T-bar handle and pull back the T-bar handle a bit. Fold
back the T-bar handle until it locks on the back brake plate. The locking mechanism and the eyelet
trigger lock together with an audible click.
D7 : You can grip the scooter by the T-bar handle and pull it behind you for easy transport.
For purposes of storage, remove both parts of the T-bar handle from the T-bar.
Press down the spring-loaded locking pins while pulling out the part sideways at the same time.
Strings inside the tubes will hold the individual part together. Clip the two parts of the T-bar handle
into the clips to both sides of the steering bar (refer to D3 in reverse order).