background image

Model GLI-9143 Portable D.O. Meter

8

Rev. 0-401

BATTERY REPLACEMENT

When the batteries are run
down "LOBAT" is displayed
on the Liquid Crystal Dis-
play.

This is to inform the user that the display will
be shut-off after about 4 hours of use to pre-
vent erroneous measurements due to low
voltage.

Battery replacement
must only take place in
a non-hazardous area
using 1.5V alkaline AA
type batteries. To
replace run-down bat-
teries, simply remove
the two screws on the
rear cover of the in-
strument and replace
the four 1.5V AA bat-
teries with new ones,
observing correct po-
larity.

A 12 VDC power adapter can also be used to
power the unit.

NOTE:

The instrument uses the following
configuration.

It is recommendable to purchase the GLI
voltage adapters that use the proper polarity
configuration. However, the meter can be
used with other adapters. In this case, re-
member to check the correct polarity of your
adapter before connecting it to the meter.

WARRANTY

GLI International, Inc. warrants the Model
GLI-9143 Hand-held/Portable Dissolved Oxy-
gen Meter to be free from defects in material
or workmanship 

for a period of one year (12

months) 

from the date of shipment of this

product from our facility. The GLI-76407/4 or
GLI-76407/10 Dissolved Oxygen Sensor is
warranted 

for a period of 6 months

. A war-

ranty claim will not be honored if defects are
not reported within the warranty period, or if
GLI International determines that defects or
damages are due to normal wear, misappli-
cation, lack of maintenance, abuse, improper
installation, alteration or abnormal conditions.
GLI International’s obligation under this war-
ranty shall be limited to, at its option,
replacement or repair of this product. The
product must be returned to GLI International,
freight prepaid, for examination. The product
must be thoroughly cleaned and any process
chemicals removed before it will be accepted
for replacement or repair. GLI International’s
liability shall not exceed the cost of the prod-
uct. Under no circumstances will GLI
International be liable for any incidental or
consequential damages, whether to person
or property. GLI International will not be liable
for any other loss, damage or expense of any
kind, including loss of profits, resulting from
the installation, use, or inability to use this
product.

Summary of Contents for GLI-9143









Reviews: