background image

 

CHAPTER SIX: WARRANTY, FACTORY REPAIR AND SAFETY 

 

6.1. Warranty 
Any product, or part thereof, manufactured by Glentek, Inc., described in this manual, 
which under normal operating conditions, in the plant of the original purchaser, thereof 
proves defective in material or workmanship within one year from the date of shipment by 
us, as determined by an inspection by us, will be repaired or replaced free of charge, FOB 
our factory, El Segundo, California, U.S.A. provided that you promptly send to us notice of 
the defect and establish that the product has been properly installed, maintained, and  
operated within the limits of rated and normal usage, and that no factory sealed  
adjustments have been tampered with.  Glentek's liability is limited to repair or  
replacement of defective parts.  

 

Any product or part manufactured by others and merely installed by us, such as an electric 
motor, etc., is specifically not warranted by us and it is agreed that such product or part 
shall only carry the warranty, if any, supplied by the manufacturer of that part.  It is also 
understood that you must look directly to such manufacturer for any defect, failure, claim 
or damage caused by such product or part.  

 

Under no circumstances shall Glentek, Inc. or any of our affiliates have any liability 
whatsoever for claims or damages arising out of the loss of use of any product or part sold 
to you.  Nor shall we have any liability to yourself or anyone for any indirect or 
consequential damages such as injuries to person and property caused directly or 
indirectly by the product or part sold to you, and you agree in accepting our product or part 
to save us harmless from any and all such claim  
 
6.2. Factory  Repair 
Should it become necessary to return a vector drive to Glentek for repair, please follow 
the procedure described below:  

1.         Reassemble the unit, if necessary, making certain that all the hardware is 
            in place.  
2.       Tag the unit with the following information:  

A. Serial number and model number.  
B. Company name, phone number, and name of representative 

returning the unit.  

C. A brief notation explaining the malfunction.  
D. Date the unit is being returned.  

3.         Repackage the unit with the same care and fashion in which it was re-

ceived. Label the container with the appropriate stickers (e.g.: FRAGILE: 
HANDLE WITH CARE).  

4.         Contact a Glentek representative, confirm that the unit is being returned 
            to the factory and obtain an RMA (Return Material Authorization) number. 
            The RMA number must accompany the unit upon return to Glentek.  

 

16 

 

Summary of Contents for SMB9675-1A-1





































Reviews: