Glasair Sportsman GS-2 Owner'S Manual Download

Page: 86 / 216

EVISION

ATE

12/29/04

AGE



approach speeds. The Sportsman can safely be slipped with full, half or

no flaps. In full- or half-flap slips, however, care must be taken to avoid

exceeding Vfe (90 kts./103 m.p.h.).

W A R N I N G

Full-flap slipping approaches should be attempted only after

becoming thoroughly familiar and proficient with the normal

handling characteristics of the Sportsman. Although the slip

itself is very straightforward, rapid transition from the slip to a

normal flare and touchdown requires confident handling of the

aircraft

4-13.6 C

ROSSWINDS

Normal crosswind landing procedures for conventional aircraft apply to

the Sportsman. Especially strong crosswinds require either a crab into

the wind and straightening out just before touchdown or a side slip, or

a combination of the two methods.
The maximum crosswind that can be handled in the Sportsman is

highly dependent on pilot proficiency and technique. Therefore,

although the Sportsman has been landed in extremely demanding

crosswind conditions, no maximum demonstrated crosswind

component is published for the aircraft. Each pilot is urged to practice

crosswind landing tasks of progressive difficulty and to honestly assess

his/her own capability along with that of the aircraft.

Summary of Contents for Sportsman GS-2


































































































































































































Search results

Summary of Contents for Sportsman GS-2

Reviews:

Related manuals for Sportsman GS-2

Brands by name

Popular brands

Glasair Sportsman GS-2, Owner'S Manual

Search results

Summary of Contents for Sportsman GS-2

Reviews:

Related manuals for Sportsman GS-2

Brands by name

Popular brands