Glasair Sportsman GS-2 Owner'S Manual Download

Page: 114 / 216

EVISION

ATE

12/29/04

AGE



6-3 FUEL SYSTEM

The standard Sportsman fuel system has two main fuel tanks and two

auxiliary fuel tanks. Capacities are 30 gallons total in the main tanks

and 20 gallons in the auxiliary tanks. All the main tanks are vented

through 1/4" diameter tubing. The vent lines extend from the

outboard ends of the tanks to the wing tips where they exit from the

lower wing surface.
Auxiliary tanks hold 10 gallons each for a total of 20 gallons extra.

Total usable fuel is 48 gallons. The auxiliary tanks feed directly into

their respective main tanks via independently operated electric transfer

pumps. Each auxiliary tank is vented to the wingtip.
The Sportsman fuel system is primarily gravity-fed. A mechanical fuel

pump on the engine supplies fuel pressure to the carburetor for a

Lycoming engine.
A two-position fuel valve with positions for fuel OFF and fuel ON is

used for fuel management. A fuel sump drain is mounted at the bottom

of each main and auxiliary tank. Additionally, a low-point drain is

located under the belly of the aircraft.
A fuel screen is fitted to the fuel pickup in each tank and a cartridge-

type fuel filter or a gascolator is required at the low point of the fuel

line forward of the firewall.
A carbureted engine can be primed with an optional hand-actuated

essex pump located on the instrument panel.

Summary of Contents for Sportsman GS-2


































































































































































































Search results

Summary of Contents for Sportsman GS-2

Reviews:

Related manuals for Sportsman GS-2

Brands by name

Popular brands

Glasair Sportsman GS-2, Owner'S Manual

Search results

Summary of Contents for Sportsman GS-2

Reviews:

Related manuals for Sportsman GS-2

Brands by name

Popular brands